CRCST Chapter 9 Quiz (9th Edition): 20 Free Questions
Published 2026-11-11 · Facts and text checked 2026-11-02 · Questions from our CRCST study guide · Reviewed by Hana N., Quality Reviewer
This free quiz has 20 questions on the topics of chapter 9, Disinfection, of the HSPA Sterile Processing Technical Manual, 9th edition: disinfectants, levels of disinfection and the Spaulding classification. They are our own questions, from our CRCST study guide, not taken from the manual. Click an answer to read the explanation.
Our own questions on the topics of chapter 9, Disinfection, of the HSPA Sterile Processing Technical Manual, 9th edition. On the exam this is part of Cleaning, Decontamination and Disinfection. Open each answer to read the explanation.
Question 1Medium
After a wash cycle, the technician reviews the cycle printout and notes that the temperature during the thermal disinfection phase reached 85°C for 90 seconds. According to mechanical verification, what does this indicate?
Show answer and explanation
Correct answer: A. The machine functioned as programmed for that parameter
The cycle printout confirms that the machine achieved the programmed temperature and time. It does not guarantee chemical indicator success, cleaning effectiveness, or sterility.
From practice test 2 of our CRCST study guide (question 29). Original question, not an official exam item.
Question 2Medium
A technician reads an SDS for a disinfectant that lists the signal word as "Warning". Which statement correctly describes the severity implied by this signal word compared to "Danger"?
Show answer and explanation
Correct answer: C. "Warning" indicates a less severe hazard than "Danger".
In the GHS system, "Danger" is used for more severe hazards, while "Warning" is for less severe hazards. There is no "Caution" signal word under GHS.
From practice test 6 of our CRCST study guide (question 116). Original question, not an official exam item.
Question 3Hard
For a non-critical item like a blood pressure cuff, which level of disinfection is typically recommended?
Show answer and explanation
Correct answer: D. Low-level disinfection
Non-critical items that contact intact skin require low-level disinfection, which kills most vegetative bacteria, some fungi, and some viruses. Intermediate-level disinfection is not required for non-critical items.
From practice test 4 of our CRCST study guide (question 120). Original question, not an official exam item.
Question 4Easy
What temperature and time combination is generally required for the thermal disinfection phase in a medical device washer-disinfector?
Show answer and explanation
Correct answer: A. 80-90°C for at least 1 minute
The standard thermal disinfection for medical device washers is 80-90°C held for a minimum of one minute. Higher temperature-time combinations are used for sterilization.
From practice test 2 of our CRCST study guide (question 26). Original question, not an official exam item.
Question 5Medium
A technician spills a small amount of a chemical disinfectant on the floor. According to the safety data sheet (SDS), which section provides the step-by-step spill response protocol?
Show answer and explanation
Correct answer: D. Section 6: Accidental Release Measures
Section 6 of the SDS provides specific spill response instructions, including absorbent type and required PPE. Section 4 covers first aid but not cleanup procedures.
From practice test 3 of our CRCST study guide (question 28). Original question, not an official exam item.
Question 6Medium
A flexible endoscope used on a patient with suspected tuberculosis must undergo reprocessing. What level of disinfection or sterilization is required?
Show answer and explanation
Correct answer: A. High-level disinfection or sterilization.
Mycobacterium tuberculosis has a waxy cell wall that makes it resistant to low and intermediate disinfection. It requires either high-level disinfection or sterilization to be reliably killed.
From practice test 5 of our CRCST study guide (question 12). Original question, not an official exam item.
Question 7Medium
In the decontamination area of a central service department, which of the following is the minimum recommended frequency for disinfecting high-touch surfaces such as countertops and sink handles?
Show answer and explanation
Correct answer: B. At least daily
High-touch surfaces must be disinfected at least daily to reduce bioburden. More frequent disinfection may be needed during heavy use, but daily is the minimum.
From practice test 3 of our CRCST study guide (question 79). Original question, not an official exam item.
Question 8Easy
According to the Spaulding classification, which of the following items is classified as critical?
Show answer and explanation
Correct answer: B. Surgical instruments that enter sterile tissue
Critical items are those that enter sterile body tissues or the vascular system and must be sterilized. Semi-critical items contact mucous membranes or nonintact skin, and non-critical items contact intact skin only.
From practice test 4 of our CRCST study guide (question 73). Original question, not an official exam item.
Question 9Medium
A technician is reading the Safety Data Sheet for a new disinfectant. To quickly identify the specific hazards and the signal word for this chemical, which section should the technician consult?
Show answer and explanation
Correct answer: A. Section 2: Hazards Identification
Section 2 of the SDS contains the hazard classification, including GHS pictograms, signal word, and hazard statements. Section 4 covers first aid, Section 6 covers spill response, and Section 8 covers exposure controls.
From practice test 4 of our CRCST study guide (question 2). Original question, not an official exam item.
Question 10Easy
A technician is preparing a 1:10 bleach solution to disinfect a work counter in the decontamination area. What minimum contact time must the solution remain wet on the surface to achieve the required reduction in bioburden?
Show answer and explanation
Correct answer: B. 10 minutes
A 1:10 bleach solution requires a minimum contact time of 10 minutes to reduce bacterial load by more than 99%. Shorter times do not allow the disinfectant to work effectively.
From practice test 4 of our CRCST study guide (question 44). Original question, not an official exam item.
Question 11Easy
A central service technician is cleaning a high-touch counter in the decontamination area with a 1:10 bleach solution. What is the minimum recommended contact time for this disinfectant to be effective?
Show answer and explanation
Correct answer: A. 10 minutes
A 1:10 bleach solution requires a 10-minute contact time to reduce bacterial load by more than 99%. Short contact times like 1 or 5 minutes do not allow sufficient kill.
From practice test 8 of our CRCST study guide (question 25). Original question, not an official exam item.
Question 12Hard
A high-level disinfectant solution is labeled with a contact time of 20 minutes at 20°C. If the solution temperature drops to 15°C, what is the expected effect?
Show answer and explanation
Correct answer: B. The contact time should be increased to compensate for reduced activity at lower temperature.
Chemical disinfectants are temperature-dependent; lower temperatures slow the rate of microbial kill. If the solution is used below the labeled temperature, the contact time must be increased to ensure adequate disinfection, per manufacturer instructions.
From practice test 4 of our CRCST study guide (question 146). Original question, not an official exam item.
Question 13Easy
Which three types of verification are required to ensure a washer-decontaminator has effectively cleaned and disinfected a load?
Show answer and explanation
Correct answer: D. Mechanical, chemical, and cleaning.
The text identifies mechanical, chemical, and cleaning verification as the three essential methods. Biological verification is for sterilization, not cleaning, and the other options list incomplete or incorrect categories.
From practice test 6 of our CRCST study guide (question 77). Original question, not an official exam item.
Question 14Hard
A technician reviews a washer-decontaminator cycle printout showing the thermal disinfection phase reached 85°C but only for 45 seconds. Which of the following is the correct interpretation?
Show answer and explanation
Correct answer: B. Thermal disinfection was not achieved because the duration was insufficient.
Thermal disinfection requires a minimum of 1 minute at 80-90°C; 45 seconds does not meet the standard, so the load must be reprocessed.
From practice test 8 of our CRCST study guide (question 32). Original question, not an official exam item.
Question 15Medium
A central service technician accidentally splashes a chemical disinfectant on their forearm. After rinsing the area with water, which section of the SDS should the technician immediately consult for further first aid instructions?
Show answer and explanation
Correct answer: C. Section 4 - First Aid Measures
Section 4 of the SDS provides specific first aid instructions for different routes of exposure, including skin contact. Rinsing is a general first step, but the SDS details any additional measures such as removing contaminated clothing or seeking medical attention.
From practice test 7 of our CRCST study guide (question 50). Original question, not an official exam item.
Question 16Hard
A technician notices that after several reprocessing cycles, a flexible endoscope still shows elevated bioburden test results despite following the manufacturer's cleaning and high-level disinfection protocol. The endoscope has a long, narrow lumen. Which of the following is the most likely explanation for the persistent contamination?
Show answer and explanation
Correct answer: B. Biofilm has formed inside the lumen and is protecting embedded organisms.
Biofilm is a sticky community of microorganisms that can form inside lumens and is resistant to disinfectants and even steam. Thorough mechanical cleaning with appropriate detergents is required to disrupt biofilm.
From practice test 3 of our CRCST study guide (question 74). Original question, not an official exam item.
Question 17Hard
A technician reviews the printout from a washer-decontaminator cycle and notices that the temperature during the thermal disinfection phase dropped to 78°C for 10 seconds before returning to the set point of 85°C. The chemical indicator shows a pass, and the load looks clean. What should be done?
Show answer and explanation
Correct answer: D. Reject the load and reprocess everything
Any temperature dip below the set point during the thermal disinfection phase means the required kill conditions were not met for the entire load, even if brief. The load must be rejected and reprocessed. Chemical indicators only confirm conditions at a single point, not the entire volume.
From practice test 3 of our CRCST study guide (question 108). Original question, not an official exam item.
Question 18Hard
After repeated cleaning and disinfection, an endoscope still shows residual bioburden in its lumen. What is the most likely explanation?
Show answer and explanation
Correct answer: A. A biofilm has formed inside the lumen, protecting microorganisms.
Biofilm is a sticky community of microbes that resists cleaning and disinfectants. It commonly forms in lumened devices like endoscopes, requiring vigorous mechanical cleaning to disrupt.
From practice test 5 of our CRCST study guide (question 67). Original question, not an official exam item.
Question 19Hard
During washer-disinfector verification, the printout shows that the thermal disinfection phase reached 80°C for 45 seconds. What action should be taken?
Show answer and explanation
Correct answer: A. Reject the load and reprocess because the hold time was insufficient
Thermal disinfection requires maintaining the specified temperature (80-90°C) for a minimum of 1 minute. A hold time of 45 seconds is inadequate, so the load must be reprocessed.
From practice test 2 of our CRCST study guide (question 81). Original question, not an official exam item.
Question 20Hard
A flexible endoscope used on a patient with a chronic urinary tract infection is processed. Despite high-level disinfection, a subsequent culture shows bacterial growth. Which factor most likely contributed?
Show answer and explanation
Correct answer: C. Biofilm inside the lumen protected bacteria from the disinfectant.
Biofilm, a structured community of microbes encased in a protective matrix, resists disinfectants and can only be reliably removed by vigorous mechanical cleaning. Even with proper disinfection, residual biofilm can harbor viable organisms.
From practice test 7 of our CRCST study guide (question 55). Original question, not an official exam item.
0 of 20 answered. Your result shows each area against our study target.
Want more mixed questions? Go back to the CRCST practice test hub.
Want the full CRCST preparation?
These questions come from our CRCST study guide: full-length practice tests with every answer explained, flashcards, an AI study tutor and the audiobook.