PrepMaster Digital
Log in

CRCST Chapter 10 Quiz (9th Edition): 20 Free Questions

Published 2026-11-14 · Facts and text checked 2026-11-02 · Questions from our CRCST study guide · Reviewed by Hana N., Quality Reviewer

This free quiz has 20 questions on the topics of chapter 10, Surgical Instruments, of the HSPA Sterile Processing Technical Manual, 9th edition: instrument types, identification and care. They are our own questions, from our CRCST study guide, not taken from the manual. Click an answer to read the explanation.

Our own questions on the topics of chapter 10, Surgical Instruments, of the HSPA Sterile Processing Technical Manual, 9th edition. On the exam this is part of Preparation and Packaging. Open each answer to read the explanation.

Question 1Medium

A technician is sorting hemostatic forceps and identifies two nearly identical clamps. The key difference between a Kelly clamp and a Crile clamp is that the Kelly clamp has:

Show answer and explanation

Correct answer: C. Horizontal serrations only at the tip.

The Kelly clamp has serrations only at the tip, while the Crile clamp has full-length serrations. This distinction is critical for secure vessel holding and appropriate tissue contact.

From practice test 5 of our CRCST study guide (question 98). Original question, not an official exam item.

Question 2Easy

When manually cleaning a set of surgical instruments with hinges and serrations, which brush type is correct to use on the stainless steel surfaces?

Show answer and explanation

Correct answer: C. A soft-bristled brush

Soft-bristled brushes are specified to avoid scratching the protective chromium oxide layer on stainless steel. Steel wool or abrasive pads can damage the surface, leading to corrosion.

From practice test 4 of our CRCST study guide (question 78). Original question, not an official exam item.

Question 3Medium

A central service technician is manually cleaning a set of hemostatic forceps. Which of the following is the most important reason to open all box locks and hinges before submerging the instruments in enzymatic detergent?

Show answer and explanation

Correct answer: C. To allow the detergent to reach all surfaces and prevent bioburden retention

Opening box locks and hinges ensures enzymatic detergent contacts every surface, including the pivot area, which is a common site for retained bioburden. If left closed, bioburden can be trapped, leading to inadequate cleaning and potential sterilization failure.

From practice test 3 of our CRCST study guide (question 8). Original question, not an official exam item.

Question 4Medium

Many facilities require multijoint retractors to be placed in an ultrasonic cleaner. What is the primary reason for this practice?

Show answer and explanation

Correct answer: A. To remove protein residues from hidden crevices

Ultrasonic cleaning reaches hidden crevices that brushes cannot, effectively removing bioburden from joints and hinges.

From practice test 7 of our CRCST study guide (question 136). Original question, not an official exam item.

Question 5Easy

A needle holder with tungsten carbide inserts is typically identified by which visual feature?

Show answer and explanation

Correct answer: A. A gold handle or gold-colored insert on the shank

Tungsten carbide inserts are often identified by a gold handle or gold-colored insert on the shank.

From practice test 7 of our CRCST study guide (question 121). Original question, not an official exam item.

Question 6Easy

A technician is inspecting Metzenbaum scissors after cleaning. Which test should be performed to check for proper blade alignment?

Show answer and explanation

Correct answer: C. Hold the blades up to a light source and look for any visible gap between them.

The gap test checks blade alignment by closing the scissors and seeing if light passes between the blades, indicating a gap. Cutting test material tests sharpness, not alignment. Ratchet and finger tests assess other aspects.

From practice test 6 of our CRCST study guide (question 69). Original question, not an official exam item.

Question 7Easy

During final inspection of a saw blade used in power tools, which of the following defects would require the blade to be removed from service?

Show answer and explanation

Correct answer: B. One of the teeth is chipped and missing a portion.

Chipped teeth indicate damage that could affect cutting performance and safety. Discoloration or scratches are cosmetic if no cracks exist. Lubricant is expected after lubrication.

From practice test 3 of our CRCST study guide (question 75). Original question, not an official exam item.

Question 8Hard

During manual cleaning of stainless steel surgical instruments, a technician uses a steel wool pad to remove dried blood from a hemostat. What is the primary risk of this practice?

Show answer and explanation

Correct answer: B. Steel wool scratches the protective chromium oxide layer.

The chromium oxide layer protects stainless steel from corrosion. Abrasive pads (including steel wool) damage this layer, leading to pitting and rust. Soft-bristled brushes are required.

From practice test 3 of our CRCST study guide (question 67). Original question, not an official exam item.

Question 9Medium

A surgeon requests scissors for cutting tough fascia during a laparotomy. Which type of scissors is most appropriate for this task?

Show answer and explanation

Correct answer: A. Mayo scissors

Mayo scissors have heavier blades designed for cutting tough tissue such as fascia, making them the correct choice for this task. Metzenbaum scissors are for fine dissection and would be inadequate.

From practice test 4 of our CRCST study guide (question 49). Original question, not an official exam item.

Question 10Easy

When arranging instruments in a sterilization tray, where should the heavier instruments be placed?

Show answer and explanation

Correct answer: A. At the bottom of the tray to provide stability and prevent damage to delicate items.

Placing heavy instruments on the bottom prevents them from crushing lighter, delicate instruments.

From practice test 2 of our CRCST study guide (question 6). Original question, not an official exam item.

Question 11Medium

During routine inspection under 3x magnification, a technician observes small, localized depressions on the surface of a hemostat. What does this finding most likely indicate?

Show answer and explanation

Correct answer: D. Corrosion that compromises the instrument's integrity.

Pitting is a sign of corrosion, which can harbor bioburden and weaken the instrument. Unlike staining, it cannot be cleaned away and renders the instrument unsafe for patient use. Normal wear does not cause pitting, and abrasives would further damage the protective layer.

From practice test 4 of our CRCST study guide (question 108). Original question, not an official exam item.

Question 12Medium

Before cleaning a Balfour retractor, the technician must:

Show answer and explanation

Correct answer: A. Disassemble it into its pieces per the IFU

The Balfour retractor has sliding lateral blades and locking threads that trap debris; disassembly per manufacturer instructions is necessary to ensure all crevices are cleaned. Soaking or ultrasonic alone cannot reach hidden areas.

From practice test 6 of our CRCST study guide (question 79). Original question, not an official exam item.

Question 13Easy

What type of lubricant should be applied to surgical instruments after cleaning and before sterilization?

Show answer and explanation

Correct answer: A. Water-soluble lubricant

Only water-soluble, instrument-safe lubricants are acceptable because oil-based lubricants can block steam penetration and compromise sterilization.

From practice test 5 of our CRCST study guide (question 110). Original question, not an official exam item.

Question 14Medium

How does a Bookwalter retractor maintain retraction without manual assistance?

Show answer and explanation

Correct answer: A. It has a locking ring that secures the blades at fixed positions

A Bookwalter retractor uses a locking ring mechanism to secure the blades at fixed positions, making it self-retaining. Spring-loaded or weighted chain mechanisms describe other retractors.

From practice test 4 of our CRCST study guide (question 117). Original question, not an official exam item.

Question 15Easy

Which category of surgical instruments does a towel clip belong to?

Show answer and explanation

Correct answer: B. Grasping instruments

Towel clips are designed to grasp and hold towels or drapes, placing them in the grasping instrument category. Cutting or clamping functions are not performed by towel clips.

From practice test 4 of our CRCST study guide (question 12). Original question, not an official exam item.

Question 16Easy

While assembling a set of scissors, a technician notices that the pivot screw is missing. What is the most likely consequence of this missing component?

Show answer and explanation

Correct answer: A. The blades will not cross properly

The pivot screw holds the blades together at the correct tension; without it, the blades separate and cannot cross properly for cutting.

From practice test 5 of our CRCST study guide (question 115). Original question, not an official exam item.

Question 17Hard

After cleaning a Balfour self-retaining retractor, a technician must verify the locking mechanism's reliability. Which action correctly tests this?

Show answer and explanation

Correct answer: A. Apply gentle outward pressure to the blades in the closed position and observe if they slip.

The locking mechanism must hold the blades securely without slipping under pressure. Gentle outward pressure simulates the force during surgery. Ratchet smoothness tests engagement, not holding strength; sliding test checks movement, not lock integrity.

From practice test 6 of our CRCST study guide (question 125). Original question, not an official exam item.

Question 18Medium

A technician needs to check a pair of Mayo scissors for proper blade alignment. Which method is correct?

Show answer and explanation

Correct answer: D. Close the blades and look for light passing between them

Scissors must meet exactly at the tip with no visible light gap when closed. This visual test assesses alignment; testing on gauze checks sharpness, not alignment, and adjusting the screw is not part of inspection.

From practice test 6 of our CRCST study guide (question 20). Original question, not an official exam item.

Question 19Medium

A technician is sorting hemostatic forceps and picks up one with horizontal serrations extending along the entire length of the jaw. Which instrument is this?

Show answer and explanation

Correct answer: C. Crile clamp

A Crile clamp has full-length horizontal serrations, whereas a Kelly clamp has serrations only at the tip. Rochester-Carmalt clamps have longitudinal serrations, and mosquito clamps are smaller with fine serrations.

From practice test 6 of our CRCST study guide (question 105). Original question, not an official exam item.

Question 20Medium

During inspection of Mayo scissors, a technician closes the blades and observes that the tips do not meet; one tip passes slightly beyond the other. Which condition does this indicate?

Show answer and explanation

Correct answer: B. The blades are misaligned at the pivot point.

When scissors blades do not meet at the tips, it indicates misalignment, often due to a loose or worn pivot screw. Dull edges do not cause tip misalignment, and a too-tight screw would prevent closure entirely, not cause crossing.

From practice test 6 of our CRCST study guide (question 109). Original question, not an official exam item.

0 of 20 answered. Your result shows each area against our study target.

Want more mixed questions? Go back to the CRCST practice test hub.

Want the full CRCST preparation?

These questions come from our CRCST study guide: full-length practice tests with every answer explained, flashcards, an AI study tutor and the audiobook.